Peli Storm IM2300 Small Electronics Case
Some gear doesn't belong in a backpack pocket or a padded sleeve. A mirrorless camera with a set of primes. A thermal imager on a job site. A portable field meter. A compact drone with a spare battery. These are the tools that define a shoot, a survey, or a diagnostic run — and they need more than good intentions to survive the journey.
The Peli Storm IM2300 was built for exactly these situations: compact enough to slip into a carry-on or a range bag, yet tough enough to meet MIL-STD-810F, IP67, and ATA 300 certification standards. It closes the gap between portability and professional-grade protection without asking you to choose between the two.
Shell That Earns Its Credentials
The case body is moulded from HPX™ resin — Peli Storm's proprietary high-performance copolymer that combines low weight with real impact resistance. It won't crack at altitude, warp in summer heat, or become brittle in hard freezes. Rounded corners and a continuous reinforced perimeter distribute shock from drops across the full shell rather than concentrating stress at a single point.
Around the entire lid perimeter, a precision-fitted O-ring gasket creates a complete airtight and watertight seal. Submerse it in a puddle. Set it on wet concrete at a construction site. The IP67 rating means the contents stay dry in up to 1 metre of water for 30 minutes — not "splash resistant," but genuinely waterproof.
Open It Without a Fight
Press & Pull latches are one of the IM2300's most practical design decisions. Press to release, pull to lock — they engage with a tactile click that confirms the seal every single time, even when wearing gloves. After a flight, when cabin pressure changes create a slight vacuum inside, the Vortex™ automatic purge valve bleeds off the differential instantly. The lid opens with a single finger.
Security Where It Counts
Padlockable hasps are integrated at each latch position, letting you run a standard padlock through both points simultaneously. Whether the case is in checked luggage, stored in a van, or sitting unattended at a location, the hardware is there when you need it. The reinforced double-hinge spans the full depth of the case and is rated to maintain alignment under repeated drops.
Configure It Your Way
The With Foam variant ships with a full Pick N Pluck™ foam set — three-layer tear-out foam in the base plus convoluted foam in the lid. Tear out the exact profiles for your camera, lenses, batteries, and accessories; the foam grips each piece individually, eliminating movement during transport. The No Foam variant leaves a clean open shell ready for your own inserts, custom trays, or mounting hardware.
Lid and base accept optional mounting panels — useful for installing small control interfaces, instrument read-outs, or screens directly into the case. Field technicians regularly use the IM2300 as a portable control enclosure as much as a storage case.
Three Colours, Same Standards
Available in Black (low-profile, universal), Yellow (high-visibility, preferred by survey and rescue teams), and Odd Green (the Peli Storm military-influenced finish, UV and chemical resistant). All three carry identical certifications: MIL-STD-810F, ATA 300, and FED-STD-101C.
Key Features
- HPX™ resin shell — lightweight, impact-resistant, temperature-stable from -40 °C to +99 °C
- IP67 waterproof — protected against submersion to 1 m depth for 30 minutes
- MIL-STD-810F / ATA 300 / FED-STD-101C certified — military and aviation durability standards
- Press & Pull latches — one-motion lock and release, glove-friendly operation
- Vortex™ purge valve — automatic pressure equalisation, opens easily after altitude changes
- O-ring gasket seal — full perimeter airtight and watertight closure
- Padlockable hasps — dual-point locking with standard padlocks
- Double-layer soft-grip handle — comfortable carry over longer distances
- Mounting panel compatibility — lid and base accept custom control or instrument panels
- Reinforced double-hinge — impact-tested lid alignment under repeated drops
- Available in Black, Yellow, and Odd Green
- With Foam or No Foam — Pick N Pluck™ three-layer customisable foam in foam variant
Original: $280.75
-65%$280.75
$98.26Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Some gear doesn't belong in a backpack pocket or a padded sleeve. A mirrorless camera with a set of primes. A thermal imager on a job site. A portable field meter. A compact drone with a spare battery. These are the tools that define a shoot, a survey, or a diagnostic run — and they need more than good intentions to survive the journey.
The Peli Storm IM2300 was built for exactly these situations: compact enough to slip into a carry-on or a range bag, yet tough enough to meet MIL-STD-810F, IP67, and ATA 300 certification standards. It closes the gap between portability and professional-grade protection without asking you to choose between the two.
Shell That Earns Its Credentials
The case body is moulded from HPX™ resin — Peli Storm's proprietary high-performance copolymer that combines low weight with real impact resistance. It won't crack at altitude, warp in summer heat, or become brittle in hard freezes. Rounded corners and a continuous reinforced perimeter distribute shock from drops across the full shell rather than concentrating stress at a single point.
Around the entire lid perimeter, a precision-fitted O-ring gasket creates a complete airtight and watertight seal. Submerse it in a puddle. Set it on wet concrete at a construction site. The IP67 rating means the contents stay dry in up to 1 metre of water for 30 minutes — not "splash resistant," but genuinely waterproof.
Open It Without a Fight
Press & Pull latches are one of the IM2300's most practical design decisions. Press to release, pull to lock — they engage with a tactile click that confirms the seal every single time, even when wearing gloves. After a flight, when cabin pressure changes create a slight vacuum inside, the Vortex™ automatic purge valve bleeds off the differential instantly. The lid opens with a single finger.
Security Where It Counts
Padlockable hasps are integrated at each latch position, letting you run a standard padlock through both points simultaneously. Whether the case is in checked luggage, stored in a van, or sitting unattended at a location, the hardware is there when you need it. The reinforced double-hinge spans the full depth of the case and is rated to maintain alignment under repeated drops.
Configure It Your Way
The With Foam variant ships with a full Pick N Pluck™ foam set — three-layer tear-out foam in the base plus convoluted foam in the lid. Tear out the exact profiles for your camera, lenses, batteries, and accessories; the foam grips each piece individually, eliminating movement during transport. The No Foam variant leaves a clean open shell ready for your own inserts, custom trays, or mounting hardware.
Lid and base accept optional mounting panels — useful for installing small control interfaces, instrument read-outs, or screens directly into the case. Field technicians regularly use the IM2300 as a portable control enclosure as much as a storage case.
Three Colours, Same Standards
Available in Black (low-profile, universal), Yellow (high-visibility, preferred by survey and rescue teams), and Odd Green (the Peli Storm military-influenced finish, UV and chemical resistant). All three carry identical certifications: MIL-STD-810F, ATA 300, and FED-STD-101C.
Key Features
- HPX™ resin shell — lightweight, impact-resistant, temperature-stable from -40 °C to +99 °C
- IP67 waterproof — protected against submersion to 1 m depth for 30 minutes
- MIL-STD-810F / ATA 300 / FED-STD-101C certified — military and aviation durability standards
- Press & Pull latches — one-motion lock and release, glove-friendly operation
- Vortex™ purge valve — automatic pressure equalisation, opens easily after altitude changes
- O-ring gasket seal — full perimeter airtight and watertight closure
- Padlockable hasps — dual-point locking with standard padlocks
- Double-layer soft-grip handle — comfortable carry over longer distances
- Mounting panel compatibility — lid and base accept custom control or instrument panels
- Reinforced double-hinge — impact-tested lid alignment under repeated drops
- Available in Black, Yellow, and Odd Green
- With Foam or No Foam — Pick N Pluck™ three-layer customisable foam in foam variant
